LED Left Right LED Headlight Upgrade For Your Car

Left Right LED Headlight

LED Left Right LED Headlight Upgrade For Your Car

The bright white light of LEDs is quickly replacing the familiar warm yellow glow of halogen bulbs. XenonPro’s LED headlight bulbs are built to last, with large aluminum bulb casings that soak up plenty of waste heat and quiet built-in fans for active cooling.

Their XB LED headlights are famed for their premiere build quality, insane light output and plug-and-play compatibility. They even come with a lifetime warranty!


One of the biggest advantages to LED headlights is their design. They’re engineered to be a plug-and-play upgrade for your vehicle. Most bulbs will fit into your original headlight bucket without issue. However, the way in which the LED chips face left to right has a lot of impact on the shape and size of your beam pattern. To get the best results, you should be sure your LED headlights are indexed and clocked in the same way as your factory lights.

This is especially important if you have a dual-beam setup. Your light modules need to focus the two beams in the same place and at the same time, so the collecting lens must be the same size and shape. This can be difficult to determine by simply looking at the bulb, but you can test them on your garage door wall with a flashlight and see how they perform.

Another advantage of LEDs is how quickly they react to brakelights. The incandescent bulb takes up to 0.2 seconds to light up, but an LED is instantly reactive. This helps the driver of the following vehicle recognize the braking action and slow down in response, which can significantly reduce your stopping distance.

The installation process can be a little tricky with some cars, but you should consult your owner’s manual for specific instructions. In general, you will need a flathead screwdriver and a socket wrench to remove the bumper cover and access the anchor points for the headlights.


LED headlights are available in DIY kits that allow you to swap your current stock bulbs for more powerful, longer lasting LED lights. These lights provide better illumination, making it easier and safer to drive at night. However, there are a Left Right LED Headlight few things you need to know before you install an LED headlight kit in your car.

The first thing you need to do is ensure your vehicle is switched off and the parking brake is on. Next, you need to remove the rubber cover on the back of the headlight just behind the halogen bulb to access the connector. Once you have done this, unplug the connector and save the old halogen bulb in a safe place.

Once you have removed the old headlight and installed the new one, make sure it is aimed properly. You want the Left Right LED Headlight LED chips to be facing left and right, not up and down. If they are positioned correctly, they will illuminate the road ahead of you and won’t blind other drivers.

Once you have installed the headlights, you can put the filler panels back in place. The LED kit comes with a bolt, nut, and washers to secure the panels to the headlight, so you should use these to attach them. Once the headlight is in place, you can plug in the gray wire from the LED light to the factory plug.


If you have a halogen headlight cluster in your car, there’s no reason to think that changing the bulbs to LED will void the warranty. Unless you actually physically break the seal by tampering with the wires, you’re safe to install new headlights from an aftermarket company like Lasfit that makes smaller sized LED replacement units that are meant to fit right in to the existing factory cluster. The kits are easy to use and you can even remove the bulbs from the headlight assembly with your hands, though we recommend wearing gloves if you do so (the oils on your fingers can cause hotspots on the quartz glass).

Most LED bulb manufacturers advertise a 30,000 hour working life, which is about 20 years of constant use. They also aren’t prone to overheating like HID bulbs, which can short circuit and stop working. It’s a good idea to read your car’s owner manual so that you’re aware of how long the lights are expected to last, and so that you know what to expect when it comes time to change them out.

When you do make the switch to LED headlights, the new lights must meet DOT (Department of Transportation) regulations to be street legal. These regulations ensure that they’re bright enough and don’t create an unreasonable risk of death or injury to other drivers on the road.


A good headlight is a must for safe night driving, and there are plenty of options to choose from. Some use famous brand names such as Philips or Sylvania, while others have unfamiliar names but promise brighter light and a longer working life than the factory halogen bulbs. Some are advertised as being able to last the lifetime of your vehicle, which would mean ten years of constant use for most drivers.

These LED bulbs use a unique hollow-carved heat sink to absorb waste and stay cool, and they are rated at 50,000 hours of operation. They also come with a three-year warranty and lifetime support from the manufacturer. They are CAN bus compatible, which means they will work with most vehicles, even those equipped with HID (high-intensity discharge) headlights that use xenon gas.

When installing a new headlight, it’s important to test them before you start driving at night. This can be done by clipping them into the harness and turning on the headlights. If they aren’t bright enough or have a weird beam pattern, you can return them. Make sure to include a picture or video to validate your warranty claim. This will ensure that the claim is processed quickly and accurately. The warranty does not cover any damage caused by environmental conditions or hard part decay, which is considered normal wear & tear.

Leave a Reply

Your email address will not be published. Required fields are marked *