LED Headlights For Left Right Vehicles

LED Headlights For Left Right Vehicles

There are a few things to consider before purchasing LED headlights. You should make sure that they meet the requirements set by your vehicle’s manufacturer and are road legal.

Also, they should have a good light beam pattern to ensure other drivers are not blinded. This is achieved by aiming them properly.


The light emitted by the headlight bulb passes through the headlight housing and lens before reaching the road. The design of the lens and housing determine how the light is reflected and directed. Different headlight assembly designs will produce different beam patterns even when using the same LED bulb.

The position of the LED chips inside the bulb can also change the beam pattern. This is especially important when the lights are installed in a projector or reflector style headlight. If the LEDs are truck lights suppliers too far in or too close, the light output is distorted. The best LED headlight bulbs will be designed with the light sources in the same position as the original halogen bulbs.

In addition, the width of the LED chip can impact the light pattern. The wider COB chips produce a more diffuse light, while CSP chips provide a more focused light output. The best LED headlight bulbs will use a CSP type of chip to deliver the most halogen-like light output.

The Vision X VX Series LED Headlight is E-MARK and ADR approved and is available in both RHD and LHD models (for countries where drivers drive on the left or right side of the road). It is also DOT compliant, so it can be used anywhere in the world.


LED headlights offer improved visibility, especially in hazy or foggy conditions. They also consume less electricity, helping to improve your fuel economy. They also don’t produce as much heat as traditional halogen bulbs, so they don’t burn out quickly. Additionally, they last longer than halogen headlights, which reduces the cost of replacing them.

The best LED headlights have a narrower width than halogen filaments, so they produce a more focused beam pattern. Look for a headlight with a light source width of 1 to 4 mm. This will ensure that the lights focus on the road ahead, instead of blinding other drivers.

Beware of three- or four-sided LED bulbs. These do not work in reflector-style headlights because they create multiple light sources that aren’t designed to fit the polished mirror surfaces of a halogen bulb housing. In this test, the gold four-sided bulb registered 150 max lux while creating a wall of light that isn’t useful in a reflector headlight.

Make sure you buy a kit that fits the headlight or fog light housing on your vehicle. The size of the housing is often listed in your owner’s manual. You can also check the spec sheet on our website to find the correct bulb for your vehicle. If you’re unsure of the size, consult an auto service technician for assistance.


Installing LED headlights on your vehicle is a simple process and does not require any special tools. All you need is a good pair of hands and the instructions manual provided to you along with the product. These instructions include pictures to eliminate any misunderstanding during the installation process.

To begin, make sure the car is off and the battery disconnected. It is also recommended that you wear gloves throughout the process so as not to contaminate the bulb with dirt Left Right LED Headlight or moisture. Next, open the hood and locate the headlight position. Unscrew the connector and pull out the existing bulb.

For LED bulbs, it is important to note that the flat side of the bulb should be facing 3 and 9 o’clock (left and right). The reason for this is that the LED chips are more concentrated and therefore produce better light output when positioned correctly in the headlight housing.

Once the new LED bulb is in place, you can re-connect the connector and test the lights. This is important because some LED headlights are aimed poorly and can cause blinding headlights for oncoming traffic. To avoid this, it is recommended that you drive your vehicle in front of a flat wall and observe the pattern that the headlights cast on the surface. The pattern should be crisp and condensed with a clear cut-off line at the top.


Unless otherwise indicated in writing, the original retail consumer purchaser and no other purchaser or subsequent owner of the Product shall have a limited warranty period of one (1) year from the date of purchase by the initial purchaser. During this time, Quake LED will repair or replace the Product (or part thereof) at no charge to the purchaser if it is determined by Quake LED to be defective.

This limited warranty does not cover damage to the headlight housing, the shutter mechanism or the lens and is non-transferable. The original retail consumer purchaser must submit a written claim of defect within the warranty period to receive this benefit. In order to process the claim, the original retail consumer purchaser must provide proof of purchase and a photograph of the defective light.

This warranty does not apply to Products that have been damaged by abuse or misuse, negligence, accident, modification, improper installation, operation outside the published environmental and electrical parameters or if the Product’s original identification (trademark, serial number) markings have been defaced or removed. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or country to country. This warranty is governed by the law of the State of Colorado, United States of America. Any dispute arising hereunder will be submitted to the jurisdiction of the courts of Denver County, Colorado.

Leave a Reply

Your email address will not be published. Required fields are marked *